Products


   

Art. No.: 22200

Flexible track, length: 730 mm.
Length: 730 mm, especially flexible.

€ 3,60



   

Art. No.: 22201

Flexible track, rigid, Length: 730 mm
Flexible track, rigid, Length: 730 mm.

€ 3,60



   

Art. No.: 22202

Straight track
Length: 312.6 mm = 3 x 22203.

€ 2,60



   

Art. No.: 22203

Standard track
Length: 104.2 mm.

€ 1,50



   

Art. No.: 22204

Adaptation track
Length 54.2 mm.

€ 1,60



   

Art. No.: 22205

Adaptation track
Length 50 mm.

€ 1,60



   

Art. No.: 22206

N track, straight.

€ 1,60



   

Art. No.: 22207

N track, straight.

€ 1,60



   

Art. No.: 22210

Re-railer track
Length 104.2 mm (corresponds to 22203). Automatic re-railer for vehicles running over the centre section.

€ 3,40



   

Art. No.: 22212

Electromagnetic uncoupler track.
Length 104,2 mm (corresponds to 22203). The builtin uncoupling part for the standard coupling can be replaced with the attached uncoupling part for short coupling operations.

€ 16,40



   

Art. No.: 22213

Rail joiners (app. 50 pieces per pack.)

€ 5,40



   

Art. No.: 22214

Insulating rail joiners (app. 24 piecs per pack.)

€ 3,60



   

Art. No.: 22215

Sleeper sections for the ends of flexible tracks.
To enhance the appearance of flexible track ends which have been cut to size, ensuring a correct sleeper spacing.

€ 0,60



  

Art. No.: 22216

Buffer stop (kit).

€ 3,40



  

Art. No.: 22217

Connecting cable, 2-pole
Connecting cable, no interference suppression.

€ 3,40



   

Art. No.: 22218

Point motor for left hand point
Point motor, suitable for N gauge points without ballast bed. Double spool operation
with end-off switching. For fitting to manual points either above or below the baseboard.

€ 19,90



   

Art. No.: 22219

Point motor for right hand points
Point motor, suitable for N gauge points without ballast bed. Double spool operation
with end-off switching. For fitting to manual points either above or below the baseboard.

€ 19,90



  

Art. No.: 22220

Power feed track with radio suppressor unit
with radio suppressor unit. Not suitable for use in digital operation.

€ 11,90



   

Art. No.: 22221

Curved track, radius R 1 (30°).
Curved track R1, raius 194,6 mm, 30°

€ 1,40



   

Art. No.: 22222

Curved track, radius R 2 (30).
Curved track R2, radius 228,2 mm, 30°

€ 1,40



   

Art. No.: 22223

Curved track, radius R 3 (30°)
Curved track R3, radius 261,8 mm, 30°.

€ 1,40



   

Art. No.: 22224

Curved track, radius R3a (30°).
Curved track R3a, radius 295,4 mm, 30°

€ 1,60



   

Art. No.: 22225

Curved track, radius R 4 (15°).
Curved track R4, radius 329 mm, 15°.

€ 1,50



   

Art. No.: 22226

Curved track, radius R4 (15°)
Curved track R5, radius 362,6 mm, 15°

€ 1,70



   

Art. No.: 22227

Curved track, radius R6 (15°).
Curved track R6, radius 480 mm, 15°.

€ 1,70



   

Art. No.: 22228

Curved track, radius R7 (12°).
Curved track R7, radius 765 mm, 12°.

Mainly used as the opposite curve for points 22301/22303

€ 1,60



   

Art. No.: 22231

Curved adaptation track, radius R1 (24°).
Curved adaptation track R1, radius 194,6 mm, 24°.

€ 1,60



   

Art. No.: 22232

Curved adaptation track, radius R1 (6°)
Curved adaptation track R1, radius 194,6 mm, 6°

€ 1,60



   

Art. No.: 22233

Curved adaptation track, radius R2 (24°)
Curved adaptation track R2, radius 228,2 mm, 24°.

€ 1,60



   

Art. No.: 22234

Curved adaptation track, radius R2 (6°)
Curved adaptation track R2, radius 228,2 mm, 6°

€ 1,60



   

Art. No.: 22235

Curved adaptation track, radius R3a (15°)
Curved adaptation track R3a, radius 295,4, 15°

€ 1,60



  

Art. No.: 22240

Transition rail joiner to Arnold® track system
(12 pieces per pack)

€ 7,40



   

Art. No.: 22244

Crossover track 30°.
Crossover track 30°, length of the diagonal 104.2 mm (4 per pack). Crossover track angle 30°.

€ 8,90



   

Art. No.: 22245

Crossover track 15°.
Longueur 112,6 mm, 4 pièces.

€ 8,90



   

Art. No.: 22246

Electric double-slip 15°.
Length of the diagonal 129.8 mm. Angle of crossing 15°.

€ 44,90



   

Art. No.: 22247

Electric three-way point 15°.
Point angle 15°, length of the straight track 112.6 mm

€ 44,90



   

Art. No.: 22249

Electric left hand point 24°
Electric left hand point. 24°.

Length of the straight track is 104,2 mm, extendable to 30° using track 22232. Radius of the branch-off track 194,6 mm (corresponds to R1).

€ 24,90



   

Art. No.: 22251

Electric right hand point. 24°
Electric right hand point. 24°.

Length of the straight track is 104,2 mm, extendable to 30° using track 22232.
Radius of the branch-off track 194,6 mm (corresponds to R1).

€ 24,90



   

Art. No.: 22253

Manual left hand point 24°
Manual left hand point. 24°.

Length of the straight track is 104,2 mm, extendable to 30° using track 22232.
Radius of the branch-off track 194,6 mm (corresponds to R1).

€ 17,40



   

Art. No.: 22255

Manual right hand point. 24°
Manual right hand point. 24°.

Length of the straight track is 104,2 mm, extendable to 30° using track 22232.
Radius of the branch-off track 194,6 mm (corresponds to R1).

€ 17,40



   

Art. No.: 22261

Electric left hand point 15°.
Electric left hand point. 15° (former Roco 22261).

Length of the straight track is 112.6 mm.
Radius of the branch-off track 326.6 mm (corresponds to R5).

€ 24,90



   

Art. No.: 22263

Electric right hand point 15°
Electric right hand point. 15°.

Length of the straight track is 112.6 mm.
Radius of the branch-off track 326.6 mm (corresponds to R5).

€ 24,90



   

Art. No.: 22265

Manual left hand point 15°.
Manual left hand point. 15°.

Length of the straight track is 112.6 mm.
Radius of the branch-off track 326.6 mm (corresponds to R5).

€ 17,40



   

Art. No.: 22267

Manual right hand point 15°.
Manual right hand point. 15°.

Length of the straight track is 112.6 mm.
Radius of the branch-off track 326.6 mm (corresponds to R5).

€ 17,40



   

Art. No.: 22273

Electric left hand curved point R1/R2
Radius 194,6 / 228,2 mm

€ 27,40



   

Art. No.: 22275

Electric right hand curved point R1/R2
Radius 194,6 / 228,2 mm.

€ 27,40



   

Art. No.: 22301

Left hand, below baseboard point (10°).
Left hand, below baseboard point.
Length of the straight track 155 mm, angle of point 10°.
Radius of the branch-off track 765 mm (corresponds to R7).

€ 16,90



   

Art. No.: 22303

Right hand, below baseboard point (10°).
Right hand, below baseboard point.

Length of the straight track 155 mm, angle of point 10°.
Radius of the branch-off track 765 mm (corresponds to R7).

€ 16,90



  

Art. No.: 6101

Standard straight track, length: 200 mm.

€ 3,30



  

Art. No.: 6102

Half straight track (for the diagonal), length 105 mm.

€ 3,50



  

Art. No.: 6103

Half straight track, length: 100 mm.

€ 3,50



  

Art. No.: 6106

Flexible track. Length: 800 mm.
Flextrack with flexible rail system. Length: 800 mm (=4 x 6101).
Suitable track connector: 6436.

€ 12,40



  

Art. No.: 6107

Straight short section (for the diagonal), length: 10 mm.

€ 3,90



  

Art. No.: 6109

Flexible track with concrete sleepers and bendable ballast base. length: 800 mm.

€ 12,40



  

Art. No.: 6110

Adjustable straight track, length: 80 - 120 mm.

€ 14,40



  

Art. No.: 6111

Uncoupler track with integrated electric motor, length: 100 mm.

€ 30,90



  

Art. No.: 6114

Uncoupler track for manual operation, length: 100 mm.

€ 12,40



  

Art. No.: 6116

Buffer stop track, length: 105 mm.

€ 9,20



  

Art. No.: 6117

Buffer stop, with end of track indicator.

€ 6,60



  

Art. No.: 6120

Standard curved track, 36° (Radius R1).

€ 4,10



  

Art. No.: 6122

Half curved track, 18° (Radius R1).

€ 4,10



  

Art. No.: 6125

Standard curved track, 36° (Radius R2).

€ 4,50



  

Art. No.: 6127

Half curved track, 18° (Radius R2).

€ 4,50



  

Art. No.: 6131

Curved track, 18° (Radius R3).

€ 4,50



  

Art. No.: 6133

Curved track, 18° (Radius R4).

€ 4,50



  

Art. No.: 6138

Curved track, 18°. Opposite curve for points

€ 4,50



  

Art. No.: 6139

Curved track, 7,5°.

€ 4,90



  

Art. No.: 6152

Electrically operated turntable
Electrically operated turntable, with electrically switchable track exits using the turntable control switch 6910. Length of the turning bridge: 310 mm.
The turntable is prototypically mounted in a recess and fitted with accurate details. As delivered, there are 6 exit tracks and 4 over-run ends. The exit tracks can be unclipped and repositioned as desired, or extended using the turntable extension set 6153 right up to the complete 48 exits.

The "thinking" turntable: using the switch 6910, will determine the rotation direction in order to access the desired exit. The power feed is activated within the turning bridge. The power to the track exit with which the turntable is lined up, either left or right, can be fed with power using the switch 6910. All other track exits remain isolated (even those opposite each other).A maximum of 48 track exits can be controlled and electrically operated without the need for any additional wiring.

Note: Control your turntables easily – with TURN-CONTROL, the electronic
turntable control device (item No. 6915).

€ 429,00



  

Art. No.: 6153

Extension set for the PROFI-track turntable 6152.
Extension set for the PROFI-track turntable 6152 for 2-rail operation with nickel silver tracks.

€ 31,40



  

Art. No.: 6155

Extension set for the smaller turntable 6154.
Extension set for the smaller turntable 6154.

The set contains 3 exit tracks and 3 over-run ends.

€ 22,90



  

Art. No.: 6157

Manual three-way point. Length: 200 mm.

€ 54,00



  

Art. No.: 6160

Crossover track, 36°, length: 105 mm.

€ 20,90



  

Art. No.: 6162

Crossover track, left hand crossing, 18°, length: 200 mm.

€ 23,90



  

Art. No.: 6163

Crossover track, right hand crossing, 18°, length: 200 mm.
.

€ 23,90



  

Art. No.: 6164

Double slip for manual operation, 18°, left hand crossing, length: 200 mm.

€ 59,00



  

Art. No.: 6165

Double slip for manual operation, 18°, right hand crossing, length: 200 mm.

€ 59,00



  

Art. No.: 6170

Standard left hand point, for manual operation. Length: 200 mm

€ 24,90



  

Art. No.: 6171

Standard right hand point, for manual operation. length: 200 mm

€ 24,90



  

Art. No.: 6174

Left hand curved point for manual operation.

€ 27,90



  

Art. No.: 6175

Right hand curved point for manual operation.
Right hand curved point for manual operation.

€ 27,90



  

Art. No.: 6178

Left hand express point for manual operation, length: 300 mm
Left hand express point for manual operation.

€ 39,90



  

Art. No.: 6179

Right hand express point for manual operation, length: 300 mm

€ 39,90



  

Art. No.: 6190

Track pack. Station Set B.
Expansion set Profi tracks:

Contents: 8 straight tracks (7x6101, 1x6103), 2 uncoupling tracks 6114, 6 curved tracks 6122, 2 curved turnouts 6174 and 6175.

€ 124,00



  

Art. No.: 6191

Track pack. Shunter Set C.
Shunter Set.

Contents: 7 straight tracks (6 x 6101, 1 x 6103), 1 uncoupler track 6114, 2 buffer stop tracks 6116, 2 curved tracks 6138, 1 left hand point 6170, 1 right hand point 6171.

€ 99,00



  

Art. No.: 6192

Track Pack. Parallel Set D.
Parallel-Set

Contents: 14 straight tracks (13 x 6101, 1 x 6103), 8 curved tracks (6 x 6125, 2 x 6127) 1 pair of curved points 6174/ 6175.

€ 129,00



  

Art. No.: 6193

Track Pack. Three-way point set E.
Three-way point set.

Contents:: 10 straight tracks 6101, 2 uncoupler tracks 6114, 2 buffer stop tracks 6116, 2 curved tracks 6138, 1 three-way point 6157.

€ 139,00



  

Art. No.: 6194

Track Pack. Platform Set F.
Platform Set

Contents: 11 straight tracks (10 x 6101, 1 x 6103), 2 uncoupler tracks 6114, 2 curved tracks 6138, 1 left hand point 6170, 1 right hand point 6171, 1 double slip turnout 6164.

€ 169,00



  

Art. No.: 619501

Electro Set for PROFI track
To convert manually operated turnouts (standard, curved, three-way and double slip turnouts) to be used for electrical operations. Contents: 1 control box 6920 for two turnouts and 1 electric turnout motor each 644110 and 644210 for left and right turnouts.
One electric set is sufficient for the electrification of each track set 6190, 6191, 6192 and 6193. 6194 requires two electro power sets.

€ 46,90



  

Art. No.: 6197

Ungated level crossing for PROFI track
Ungated level crossing for PROFI track. With one rerailer and two level crossing signs.

€ 14,90



  

Art. No.: 6199

Reverse loop set to deal with driving on reverse loops
Reverse loop set to deal with driving on reverse loops.

The set consists of isolating joints and 2 directional track sections. Length: 100 mm each. Two level crossings. Can not be controlled digitally.

€ 39,90



 

Art. No.: 640000

Electromagnetic universal point motor with end-off switching
Electromagnetic universal point motor with end-off switching for FLEISCHMANN ballasted tracks H0 and N.
Prepared to accept the clip-in illuminated point lantern 644020 (H0) / 944001 (N)

This point motor can be either plugged onto the railway layout board or underneath the railway layout board. For this purpose, a slot is cut into the railway layout where the point motor comes to rest.

The universal point motor 640000 replaces the items 644110, 644210, 942101 and 942201.

€ 21,90



 

Art. No.: 6410

Wood-screws
Wood screws to fasten tracks, rackrails, signals, relays and signal box parts.

Content: 144 pieces

€ 13,90



  

Art. No.: 6412

Flexible rack track for PROFI track. Length: 200 mm
Flexible rack track for H0 PROFI track.

Flexible - to install in straight or curved tracks. Suitable for all radii (R1 - R4).
Length: 200 mm.

€ 5,40



  

Art. No.: 6430

Track Feed Clips ( 2-pole)
Track feed clips (2 poles) can only be connected to the rail connectors on each rail joint. Saves a siding.

€ 5,40



  

Art. No.: 6431

Track Feed Clip (1-pole)
Track feed clip (1 pole).

Track feed clips can only be connected to the rail connectors on each rail joint such as infront or behind the electrical cut-off point or with signal circuits.

€ 3,90



  

Art. No.: 6432

Switch contact rail, 1-pole
Switching rail (1 pole).

To trigger off switching impulses for turnouts, signals etc. with driving locomotives. Can be used on any section of the railway layout.

Set contents: 1 plastic pin, 1 fastening part and 1 track feed clip, 1 switching rail.

€ 5,90



  

Art. No.: 6433

Isolating rail joiners
Isolating rail joints for electrical rail cut-off. Can be used on any layout section. The mechanical connection is maintained. (12 pieces)

€ 4,60



  

Art. No.: 6434

"Click" metal rail joiners
Click rail joiners. To electrically and mechanically connect a rail track assembly. Can not be used for 6106/6109. (20 pieces)

€ 7,40



  

Art. No.: 6435

Switch contact
Switch contact to trigger off electrical switching impulses up to a max. of 800 mA. Can be connected to the solenoid switches 942601 and 942701.

Contents: 1 piece

€ 19,90



  

Art. No.: 6436

Metal rail joiners
Metal rail joints. Transitional rail joints from assortment 6000 to assortment 6100. To connect the flexible tracks 6106/6109. (20 pieces)

€ 7,90



  

Art. No.: 6437

Transitional rail joints
Transitional rail joints to connect Scale H0 tracks of 2.5 mm rail profile height with tracks of 2.1 mm rail profile height. (20 pieces)

By simply exchanging the standard mounted rail joints to the transitional rail joints 6437 you can adjust the turntable and the expansion set 6155 to track layouts of 2.1 mm high rail profiles.

€ 7,90



  

Art. No.: 6438

Illuminated point lantern
Point lantern to optionally retrofit for a left, a right or a three-way point. Illumination with maintenance-free LEDs. From the turnout independent power supply.
Can not be used with double slip switches and high-speed switches.

€ 18,90



  

Art. No.: 644020

Illuminated point signal for PROFI track
Illuminated point signal for PROFI track.

To clip onto point motor 640000

€ 13,40



  

Art. No.: 644110

Left hand point motor for PROFI track.

€ 18,60



  

Art. No.: 644210

Right hand point motor for PROFI track.

€ 18,60



  

Art. No.: 6444

Electrical plug-in motor for item 6114
Electrical plug-in motor for manually operated uncoupling track 6114.

€ 22,90



  

Art. No.: 6476

Loco Roundhouse (kit)
Suitable for use with the turntables 6052, 6152, 6154 and 6651. 3 loco stalls set at 7,5° angles with 8 opening doors.Outstandingly detailed plastic parts, loads of individual parts for individual decoration. The doors are operated by locos leaving and entering the shed. One set of doors is set at the rear of the shed to run straight through if desired.Several roundhouse kits can be set up alongside each other to make up a large shed.As a tip to modellers, the lighting unit 6459 can be fitted insdie.

€ 109,00



  

Art. No.: 6480

Rerailer
Rerailer for locos and wagons (without vehicle shown).

€ 5,90



 

Art. No.: 6910

Turntable switch
To operate the electric turntables with electrically switchable track exits.

€ 44,40



 

Art. No.: 6915

Turntable Controller with track pre-selection
The modern turntable control unit is suitable for analogue and digital control of the turntables from the FLEISCHMANN range and the Märklin® turntable, item no. 7286. An LCD display gives a visual indication of the setting of the turntable bridge, the location of the track exits installed and shows the active track exit, together with additional functions. Symbols of the active functions give it a simple, user-friendly operation. Each track exit can be individually controlled. Because the polarity change is catered for by the switch, when rotating through 180°, the turntable is protected against short circuit. The turntable control switch is suitable for operation wtih 2-rail DC operation, the 3-rail AC operation, and will also operate with all digital systems - DCC, FMZ and Märklin®-Digital (contains a turntable decoder). No changes or alterations to the turntable are necessary.

Märklin is a registered trademark of the company of Gebr. Märklin & Cie. GmbH, Göppingen.

€ 219,00



 

Art. No.: 81398

Manual FLEISCHMANN H0 PROFI tracks with ballast bed
The track plan manual explains the geometry of the FLEISCHMANN PROFI tracks in scale H0. The manual gives some useful and practical ideas and also shows many track layouts and expansion options in details. All featured track layouts are provided with layout designs and parts lists.

€ 9,95



 

Art. No.: 81399

Track Manual FLEISCHMANN N gauge (for ballasted tracks)
The track plan manual explains the geometry of the ballasted tracks of FLEISCHMANN in scale N. Many track layouts and expansion options are shown in details.
All featured track layouts are provided with parts lists.

€ 9,95



  

Art. No.: 9100

Straight track. Length: 222 mm.
Straight track 222mm.

€ 3,60



  

Art. No.: 9101

Straight track, length 111 mm.
Straight Railtrack 111mm.

€ 3,60



  

Art. No.: 9102

Straight track, length 57.5 mm.
Straight Railtrack 57,5 mm.

€ 3,60



  

Art. No.: 9103

Straight track, length 55.5 mm
Straight Railtrack 55,5mm.

€ 3,60



  

Art. No.: 9104

Straight track, length 27.75 mm.
Straight Railtrack 27,25mm.

€ 3,60



  

Art. No.: 9106

Flexible track, length 777 mm.
Flexible track with bendable track bed

€ 12,90



  

Art. No.: 9108

Straight track, power feed track, with interference suppressor, length 111 mm
Straight connecting track 2 poles, with suppressor

€ 21,90



  

Art. No.: 9110

Straight extendable track, length 83 to 111 mm.

€ 12,40



  

Art. No.: 9112

Uncoupler track with electric motor, length 111 mm.

€ 27,40



  

Art. No.: 9114

Manual uncoupler track, length 111 mm.

€ 12,90



  

Art. No.: 9115

Straight track with inbuilt switch contact, length 55.5 mm.

€ 21,40



  

Art. No.: 9116

Buffer stop, length 57,5 mm.

€ 6,90



  

Art. No.: 9117

Adapter track to link with the ARNOLD® track system, length 111 mm.

€ 4,90



  

Art. No.: 9119

Flexible rack track, length 222 mm.
Flexible rack track, length 222 mm.

This track can be curved to the desired radius, even down to the minimum radius (9120) The rack section always remains the same length, although the rail section will need to be trimmed to length accordingly.
The rails can be joined using the rail joiners 9403 or 9404.

€ 7,90



  

Art. No.: 9120

Curved track, radius R1, 45°

€ 3,40



  

Art. No.: 9122

Curved track, radius R1, 15°.

€ 3,50



  

Art. No.: 9123

Curved track, radius R1, 7.5°.

€ 3,50



  

Art. No.: 9125

Curved track, radius R2, 45°..

€ 3,70



  

Art. No.: 9127

Curved track, radius R2, 15°.

€ 3,70



  

Art. No.: 9128

Curved track, radius R2, 7.5°.

€ 3,40



  

Art. No.: 9130

Curved track, radius R3, 30°.

€ 4,00



  

Art. No.: 9131

Curved track, radius R3, 15°.

€ 4,00



  

Art. No.: 9135

Curved track, radius R4, 30°.

€ 4,00



  

Art. No.: 9136

Curved track, radius R4, 15°.

€ 4,00



  

Art. No.: 9152

Electrically operated turntable
Model Turntable, electrically driven, with individual electrically switchable track exits, with turntable switch 6910. Length of the turning bridge 183 mm.

The Model:
The turntable is sunk into the ground, exactly like the real thing and is complete with all the correct detailling. The basic turntable has 6 exit tracks and 4 stub tracks. The track exits are set at 7,5° intervals, but can be altered if desired, or extended with the extension set 9153 up to total of 48 track exits.

The "thinking" turntable: The turntable movement is controlled by using the switch 6910, in order to reach the desired track exit. The track power feed is via the turntable bridge. Now the switch 6910 will enable the desired track exit, which is lined up with the turntable, to be electrically switched on. All the other track exits (even one directly opposite) will remain without power. In this way, each of the maximum of 48 track exits can be individually controlled and electrically switched on, without the need for any additional wiring.

Note: Control your turntables easily – with TURN-CONTROL, the electronic
turntable control device (item No. 6915).

€ 349,00



  

Art. No.: 9153

Turntable extension set for turntable 9152
Turntable extension set for turntable 9152 containing 3 exit tracks and 3 over-run ends.

€ 26,90



  

Art. No.: 9157

Three-way point for manual operation, length 111 mm.
Point motors can be clipped onto the three-way point and switched as a "thinking" point. The two curved exits correspond to the track 9136 (15°).

€ 42,90



  

Art. No.: 9161

Crossover 30°, length 115 mm
Crossover 30°, length 115 mm.

The crossover 9161 is fitted with check rails and frogs. The crossing tracks are isolated from each other. The length of the diagonally crossing track measures 115 mm (= 2 x 9102 "diagonal" track).

€ 19,90



  

Art. No.: 9162

Crossover 15°, left hand crossing, length 111 mm
Crossover 15°, left hand crossing, length 111 mm.

The crossing tracks are isolated from each other so that two independent power circuits can cross each other.
Track 9136 serves as opposite curve and leads to the parallel track distance of 33.6 mm.

€ 29,90



  

Art. No.: 9163

Crossover 15°, right hand crossing, length 111 mm
Crossover 15°, right hand crossing, length 111 mm.

The crossing tracks are isolated from each other so that two independent power circuits can cross each other.
Track 9136 serves as opposite curve and leads to the parallel track distance of 33.6 mm.

€ 29,90



  

Art. No.: 9168

Left hand curved point for manual operation with current-conducting frog
Left hand curved point for manual operation, with current-conducting frog. Adaptable with electric point motor.
To change from radius R1 to radius R2 and viceversa, 45°.

€ 32,90



  

Art. No.: 9169

Right hand curved point for manual operation with current-conducting frog.
Right hand curved point for manual operation, with current-conducting frog. Adaptable with electric point motor.
To change from radius R1 to radius R2 and viceversa, 45°.

€ 32,90



  

Art. No.: 9170

Left hand standard point for manual operation, length 111 mm
Left hand standard point for manual operation. Adaptable for electric point motor.
Track 9136 serves as opposite curve and leads to the parallel track distance of 33.6 mm.

€ 21,90



  

Art. No.: 9171

Right hand standard point for manual operation, length 111 mm
Right hand standard point for manual operation. Adaptable for electric point motor.
Track 9136 serves as opposite curve and leads to the parallel track distance of 33.6 mm.

€ 21,90



  

Art. No.: 9174

Left hand curved point for manual operation
Left hand curved point for manual operation. Adaptable with electric point motor.
To change from radius R1 to radius R2 and viceversa, 45°.

€ 26,40



  

Art. No.: 9175

Right hand curved point for manual operation
Right hand curved point for manual operation. Adaptable with electric point motor.
To change from radius R1 to radius R2 and viceversa, 45°.

€ 26,40



  

Art. No.: 9178

Left hand standard point for manual operation, with current-conducting frog. Length 111 mm
Left hand standard point for manual operation, with current-conducting frog. Adaptable with electric point motor.
Track 9136 serves as opposite curve and leads to the parallel track distance of 33.6 mm.

€ 26,40



  

Art. No.: 9179

Right hand standard point for manual operation, with current-conducting frog. Length 111 mm.
Right hand standard point for manual operation, with current-conducting frog. Adaptable with electric point motor.
Track 9136 serves as opposite curve and leads to the parallel track distance of 33.6 mm.

€ 26,40



  

Art. No.: 9184

Double slip for manual operation, left hand crossing, 15°, length 111 mm.
Double slip for manual operation, left hand crossing, 15°.
Adaptable for electric point motor. Track 9136 serves as opposite curve and leads to the parallel track distance of 33.6 mm.

As delivered, all track exits deliver power into one circuit. By removing the wire bridge clips the crossing tracks become electrically isolated from each other.
On the ”crossover“ setting, another track circuit can be traversed. On the ”branch-off“ setting, the current is separated at the centre of the slip.

€ 49,90



  

Art. No.: 9185

Double slip for manual operation, right hand crossing, 15°. Length: 111 mm
Double slip for manual operation, right hand crossing, 15°.
Adaptable for electric point motor. Track 9136 serves as opposite curve and leads to the parallel track distance of 33.6 mm.

As delivered, all track exits deliver power into one circuit. By removing the wire bridge clips the crossing tracks become electrically isolated from each other.
On the ”crossover“ setting, another track circuit can be traversed. On the ”branch-off“ setting, the current is separated at the centre of the slip.

€ 49,90



  

Art. No.: 9189

Track pack. Station Set B
Containing: 4 straight tracks 9100, 2 uncoupler tracks 9114 as well as 1 left hand curved point 9174 and 1 right hand curved point 9175 to create a passing loop of longer „platform tracks"

€ 89,00



  

Art. No.: 9190

Track pack. Shunter Set C
Containing: 6 straight tracks 9100, 1 uncoupler track 9114, 2 buffer stops 9116, 2 curved tracks 9136 as well as 1 left hand point 9170 and 1 right hand point 9171.

€ 99,00



   

Art. No.: 919001

Track Set A1
Content: 1 straight track 9100, 1 straight track 9101, 1 right hand point 9171, 1 buffer stop 9116

€ 29,90



   

Art. No.: 919002

Track Set BÜ, with level crossing
Contents: 1 straight track 9101, 2 straight tracks 9104, 1 buffer stop 9198

€ 39,90



   

Art. No.: 919003

Track Set Ü1, passing track 1
Contents: 2 straight tracks 9100, 2 curved tracks 9136 (opposite curve for points), 1 right hand point 9171

€ 29,90



   

Art. No.: 919004

Track Set Ü2, passing track 2
Contents: 3 straight tracks 9100, 3 straight tracks 9101, 2 curved tracks 9136 (opposite curve for points), 2 manual uncoupler tracks 9114, 1 left hand point 9170, 1 right hand point 9171

€ 76,00



   

Art. No.: 919083

DCC digital, Track Set Ü1
Contents: 2 straight tracks 9100, 2 curved tracks 9136 (opposite curve for points),
1 right hand point 9171, 2 electric point motors, 1 x 9414 (clip-on electric motor for manual uncoupler track 9114),
1x 8-fold turnout decoder DCC 10775,
1x 3-pole cable 10623,
3x 3-pole connector 10603

€ 149,00



   

Art. No.: 919084

DCC digital, Track Set Ü2
Contents: 3 straight tracks 9100, 3 straight tracks 9101, 2 curved tracks 9136 (opposite curve for points), 2 uncoupler tracks with electric motor 9112, 1 x 9414 (clip-on electric motor for manual uncoupler track 9114),
1 left hand point 9170, 1 right hand point 9171, 3 electric point motors,
1x 8-fold turnout decoder DCC 10775,
1x 3-pole cable 10623,
6x 3-pole connector 10603

€ 229,00



  

Art. No.: 9191

Track pack. Complete Set D

€ 119,00



  

Art. No.: 9194

Track pack. Three-way point Set E

€ 129,00



  

Art. No.: 919501

Electro Set to retrofit manual turnouts with electric drive
The set can convert manually operated turnouts to electromagnetic turnouts. Remote control via control box.
Can be used for standard, curved, three-way and double slip turnouts.
Contents: 2 turnout motors, 1 switcher 6920.
One electric set is sufficient for the electrification of each track set 9189, 9190, 9191 and 9194.

€ 47,40



  

Art. No.: 9196

Track pack. Platform Set F

€ 159,00



  

Art. No.: 9400

Track feed clips, 2 x 1 pole

€ 5,00



  

Art. No.: 9401

Connecting wire with flat contact springs
Single pole connecting wire and clips for train control operation of semaphore signals.

€ 4,00



  

Art. No.: 9403

Isolating rail joiner

€ 5,40



  

Art. No.: 9404

Metal rail joiner

€ 5,00



  

Art. No.: 9409

Track fixing nails
Track Fixing Nails. Nail length 7 mm (approx. 500 pcs.) in a plastic container.

€ 7,90



  

Art. No.: 9414

Clip-on electric motor for the manual uncoupler track 9114
Clip-on electric motor for the manual uncoupler track 9114.

€ 23,40



  

Art. No.: 942201

Right hand point motor for N track

€ 18,40



  

Art. No.: 9425

Magnetic switch contact
Switch contact to fit into trackwork. The switching impulse (max. 800 mA) is activated using the magnets 942601 or 942701 fitted to the train.

€ 21,90



  

Art. No.: 942601

Switching magnet, angular
To activate the switch contacts 6435 and 9425 or the switching track 9115.

To fix onto the underside of vehicles. Surface area 7 x 7 mm, height 5 mm.

€ 3,90



  

Art. No.: 942701

Switch magnet, circular
To activate the switch contacts 6435 and 9425 or the switching track 9115.

To fix onto the underside of vehicles. Diametre: 5 mm, height 3 mm.

€ 3,90



  

Art. No.: 944001

Illuminated point lantern signal for N track with ballast bed

€ 13,40



  

Art. No.: 9479

Track ballast
Track ballast.

Finely grained ballast scatter to go between tracks.

€ 7,20



  

Art. No.: 9480

Re-railer
Re-railer for ease of placing vehicles on the track.

€ 4,90



  

Art. No.: 9900

TRACK PLAN BOOKLET H0
Detailed illustration of the starter sets and track sets. Additional small tips. DIN A 5, 4 colours.

€ 1,80



  

Art. No.: 9921

Track stencil for Fleischmann H0 PROFI-track
Track stencil for Fleischmann H0 PROFI-track.

An absolutely essential aid for individual layout planning. Transparent, yellow plastic, scale 1:10.

€ 19,90



  

Art. No.: 995101

Track Stencil for N gauge.

€ 19,90